95 photos of the correct construction of a reliable access road


Many owners of private country houses are faced with one very difficult task, this is a gutter at the entrance to their site and how to make an entrance to the site through a ditch. As a rule, most owners of private houses would solve this issue very primitively, it’s just to fill a small part of the ditch with sand or gravel, but this is not an option in this situation. This raises a reasonable question, how to find the optimal solution in this case.

It should be noted that entry into your territory must be reliable and meet all requirements. However, it is important to pay attention to the strength and reliability of the platform itself, which must withstand heavy loads from the weight of the car, and there must also be a normal flow for sewage, this is very important.

Therefore, the solution to this issue can be found in this article, which also contains various and colorful photos of the entrance to the site.

Brief content of the article:

Installation of narrow width entry

This method of solving this problem of driving to a summer cottage is considered quite simple, but the cost of the material to complete such a task will be very high. Therefore, this option is not suitable for large barriers, especially when it comes to barriers with wide openings.

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement
Watch the video: Ennoble the entrance to the site

In this case, it is necessary to use concrete slabs of large dimensions, while the cost of the slab depends on its size. And these can be very significant numbers.

So, how do you apply for entry? At the initial stage, it is necessary to determine what kind of soil is located in the extreme sections of the channel, since they need to be strengthened as necessary. If this is not done, then from the mass of the car and the plate itself, it can sag or simply fall apart.

Next, you need to build an additional fortification. A formwork should be made near the concrete supports, in which there should be a reinforced double structure, after which concrete can be poured into the formwork. And it is recommended to sprinkle the resulting free space between the supports and the walls with sand or clay.

If the material intended for the channel has a large width and thickness, in this case it is recommended to dig the soil along the thickness of the slab.

At the final stage, the finished site is well leveled, and also carefully rammed. In this case, the sand layer should be no more than 7 cm, similarly, the gravel layer. The laying of the slab is carried out by special construction equipment.

It should be noted that it is almost impossible to make an entrance to the site through a ditch without resorting to the services of special equipment, and even on your own.

Further, with the help of equipment, it is necessary to lay the slab on the finished site, while the ratio of the height of the slab to the ground is important. So if there is a lot of soil, then it must be removed, but if it is not enough, then you will have to add it.

Installation of a wide platform with sides

This method of mounting a drive into your territory through a ditch is not expensive, but the implementation process is very laborious and lengthy. Its greatest difficulty is due to the fact that sewage can flow through the ditch.

So, if there is water in a dug recess, it must be pumped out immediately. However, many do not do this at all, and in vain. The fact is that if you mount the formwork in the water, where the concrete will then be poured, this will affect the quality of the structure. In this case, it is likely that the structure may simply collapse very quickly.

Further, it is necessary to install dividing partitions at a small distance between them. As a partition, you can use slate, wood or other building materials. Then you can start pumping water in each individual area.

After that, a small layer of sand is poured into the prepared channel over the entire surface, and then a plentiful layer of gravel, and it is recommended to compact all this well with a vibrating plate.

A special pipe for draining water can be laid in the finished channel, while it must be fixed in one position using an ordinary brick. Further, on both sides, at the edge of the pipe, formwork must be mounted, having a height slightly greater than the channel walls.

The formwork must necessarily contain a reinforcement structure, and only then can concrete mortar be poured into the finished formwork. After pouring concrete, wait until the structure is completely dry.

Then it is necessary to strew the pipe with gravel in several layers, while each subsequent gravel layer should have a smaller and smaller fraction, one should not forget that each gravel layer must be well compacted.

A thin layer of granite chips can be poured onto a previously prepared site and compacted again, and at the end it is necessary to cover it with a slight layer of sand. And upon completion, on the finished site, small stones or broken bricks can be applied to a height of not more than 5 cm, after which a special mesh connected from reinforcement is laid on this surface.

Along the edges and around the entire perimeter, small road bumpers are mounted. And only after that, the site can be poured with concrete mortar, no more than 7-8 cm high.

For a preliminary calculation of the material, it is required to measure the height and width of the channel. As needed, you can make the ditch deeper, while keeping in mind that the deepening should be done smoothly and with a slight angle. This is necessary for a good stack of water, if this is not observed, then the water will not drain and will stand in one place.

Therefore, making a good check-in on your territory is not as easy as it might seem at first glance. Performing this work, you may encounter various difficulties that require some effort.

At the same time, you need to understand that you need to adhere to a clear plan of action, otherwise the end result will be very bad, if you are not confident in your abilities, then in this case you need to contact specialists who have special equipment for such work. Therefore, it is almost impossible to independently make an entrance to the site with your own hands.

If you have any difficulties or doubts, you can order entry to the turnkey site, and you will save a lot of your time and effort. However, in this case it will require certain financial costs, but these costs are worth it. At the same time, the masters will fulfill all your requirements and wishes.

Photo of the entrance to the site

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement

Entrance to the site - modern solutions for arrangement


Save the article to your page:

Post published: 14.10

Join the discussion:

Copyright © 2022 LandshaftDizajn.Ru — landscape design portal №1

***Site owned by Maria Kozak


Добавить комментарий